AS 1832-2007 Malleable cast iron
|
ID： |
8CA69F96EA254E688C93FEA21CCD6D3D |
|
文件大小(MB)： |
0.6 |
|
页数： |
21 |
|
文件格式： |
|
|
日期： |
2009-6-26 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
AS 1832—2007,ISO 5922:2005,Australian Standard?,Malleable cast iron,AS 1832—2007,This Australian Standard?was prepared by Committee MT-001, Iron and Steel. It was,approved on behalf of the Council of Standards Australia on 8 December 2006.,This Standard was published on 29 January 2007.,The following are represented on Committee MT-001:,?Australian Railway Association,?Australian Building Codes Board,?Australian Foundry Institute,?Australian Industry Group,?Australian Steel Industry,?Bureau of Steel Manufacturers of Australia,?Institute of Materials Engineering Research Association,?New Zealand Heavy Engineering Research Association,This Standard was issued in draft form for comment as DR 06613.,Standards Australia wishes to acknowledge the participation of the expert individuals that,contributed to the development of this Standard through their representation on the,Committee and through public comment period.,Keeping Standards up-to-date,Australian Standards?are living documents that reflect progress in science, technology and,systems. To maintain their currency, all Standards are periodically reviewed, and new editions,are published. Between editions, amendments may be issued.,Standards may also be withdrawn. It is important that readers assure themselves they are,using a current Standard, which should include any amendments that may have been,published since the Standard was published.,Detailed information about Australian Standards, drafts, amendments and new projects can,be found by visiting www.standards.org.au,Standards Australia welcomes suggestions for improvements, and encourages readers to,notify us immediately of any apparent inaccuracies or ambiguities. Contact us via email at,mail@standards.org.au, or write to Standards Australia, GPO Box 476, Sydney, NSW 2001.,下载,AS 1832—2007,Australian Standard?,Malleable cast iron,Originated as AS G11—1962, AS G12—1962 and AS G14—1969.,Previous edition AS 1832—2002.,Fourth edition 2007.,COPYRIGHT,. Standards Australia,All rights are reserved. No part of this work may be reproduced or copied in any form or by,any means, electronic or mechanical, including photocopying, without the written,permission of the publisher.,Published by Standards Australia, GPO Box 476, Sydney, NSW 2001, Australia,ISBN 0 7337 7990 5,ii,PREFACE,This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee,MT-001, Iron and Steel, to supersede AS 1832—2002, Malleable cast iron,After consultation with stakeholders in both countries, Standard Australia and Standards New,Zealand decided to develop this Standard as an Australian, rather than an Australian/New,Zealand Standard.,This Standard is identical with, and has been reproduced from ISO 5922:2005, Malleable cast,iron.,The objective of this Standard is to specify grades of malleable cast irons which have been,classified by mechanical properties.,This Standard is one of a series of Standards covering the range of tensile testing methods. The,series comprises the following:,AS,1830 Grey cast iron,1831 Ductile cast iron,1832 Malleable cast iron (this Standard),1833 Austenitic cast iron,1982 Methods for the measurement of case depth in steels,2027 Abrasive-resistant cast irons,2074 Cast steels,4314 Founding—Patterns, pattern equipment and coreboxes for the production of,sand moulds and sand cores,4738 Metal castings,4738.1 Part 1: Ferrous sand moulded,5049 Cast iron—Designation of microstructure of graphite,5052 Compacted (vermicular) graphite cast irons—Classification,5054 Ausferritic spheroidal graphite cast irons—Classification,5080 Ferrous materials—Heat treatment—Glossary of terms,As this Standard is reproduced from an International Standard, the following applies:,(a) Its number does not appear on each page of text and its identity is shown only on the,cover and title page.,(b) In the source text ‘this International Standard should read ‘this Australian Standard’.,(c) A full point should be substituted for a comma when referring to a decimal marker.,(d) Where the ISO Standard number is shown (i.e. ISO 5922) in a malleable cast iron,specification, it should be read as ‘AS 1832’.,下载,iii,References to International Standards should be replaced by references to Australian Standards,as follows:,Reference to International Standard Australian Standard,ISO AS,148 Steel—Charpy pendulum impact test,(V-notch),1544 Methods for impact tests on metals,148-1 Part 1: Test method 1544.2 Method 2: Charpy V-notch test,148-2 Part 2:Verification of test machines,148-3 Part 3:Preparation and characterization,of Charpy V reference test pieces for,verification of test machines,6506 Metallic m……
……